3400, 10180 101 St NW, Edmonton, AB T5J 3S424/7 service 1 (800) 716-8955
  1. Home
  2. Guides
  3. Instrumentation, controls and automation
  4. How to set instrument calibration schedules
Instrumentation, controls and automation

How to set instrument calibration schedules

A practical approach to deciding how often each instrument gets calibrated, what a good calibration record contains, and how to adjust intervals using your own data.

7 min readFor facility managers2 illustrations

Why calibration drifts out of sight

Every measuring instrument drifts. Pressure transmitters shift with temperature cycling and vibration, gas sensors lose sensitivity as they age, flow meters wear, and temperature sensors can open up or degrade. Most of the time the reading still looks believable, which is exactly the problem.

A calibration program catches drift before it causes a bad batch, a missed alarm, a wasted energy bill or an incident. The hard part is not the calibration itself. It is deciding which instruments, how often, and to what standard, then sticking to it.

Good to knowWho does the work

In Alberta, Instrument Technician is a designated trade of its own. Calibration and adjustment of process instruments is normally done by instrument technicians, with electricians handling power and wiring.

Start with an instrument list

You cannot schedule what you have not listed. Build or clean up an index with, at minimum:

  • Tag number and location
  • What it measures and its calibrated range
  • What it does: indicate, control, alarm, shut down, or report to a regulator or customer
  • Make, model and serial number
  • Required accuracy (tolerance) for its job
  • Last calibration date and result

Many sites find instruments during this step that nobody knew existed, or that have been disconnected for years. It is worth walking the site with the drawings in hand.

Rank by criticality

Not every gauge deserves the same attention. A common method sorts instruments into tiers based on the consequence of a wrong reading.

FIG 01Alberta Electrical
Flow chart of four inputs feeding a criticality ranking that sorts instruments into three calibration tiers. SETTING THE INTERVAL SAFETY ORREGULATORY ROLE? COST OF AWRONG READING MANUFACTURERGUIDANCE DRIFT HISTORY(AS-FOUND DATA) CRITICALITYRANKING TIER 1: SHORTESTINTERVAL TIER 2: STANDARDINTERVAL TIER 3: LONGER ORRUN-TO-FAIL
Interval decisions combine the instrument's role, the cost of an error, manufacturer guidance and real drift history into a criticality tier.
TierTypical examplesApproach
1: criticalSafety shutdowns, gas detection, custody transfer or regulatory reporting, product qualityShortest interval, documented procedure, strict tolerance, verify after any repair
2: importantControl loops that affect efficiency or equipment life, energy meteringRegular interval, adjust based on as-found history
3: indicationLocal gauges, non-critical trend pointsLonger interval, check opportunistically or replace on failure

We deliberately do not give fixed months here. The right interval depends on the device, the manufacturer's recommendation, any regulation or permit condition that applies, and your own drift data. For gas detectors in particular, follow the manufacturer's bump test and calibration requirements and any rules that apply to your workplace.

SafetyRegulated instruments come first

Where an instrument is used for safety, environmental reporting or billing, the interval and method may be set by a regulator, permit, contract or standard. Confirm those requirements before you set your own schedule.

What a good calibration record shows

A record should let someone else repeat the work and trust the result. Look for:

FIG 02Alberta Electrical
Diagram of a reference standard feeding an instrument under test, with a chart of as-found errors drifting past a tolerance line and as-left errors near zero. FIVE-POINT CALIBRATION CHECK REFERENCE STANDARD INSTRUMENT UNDER TEST MEASURED OUTPUT (mA OR READING) ERROR 0 TOLERANCE LIMIT 0%25%50%75%100% AS FOUND (OUT AT TOP) AS LEFT (ADJUSTED)
A calibration compares the instrument against a traceable reference at several points across its range, recording errors before (as found) and after (as left) adjustment.
  • As-found readings at several points (often 0, 25, 50, 75 and 100 percent) before anything is touched
  • As-left readings after adjustment
  • The tolerance it was checked against and a pass or fail
  • The reference equipment used, with its own calibration certificate traceable to national standards
  • Date, technician and any notes on condition, damage or repairs

The as-found data is the valuable part. It tells you whether the instrument was out of tolerance while it was in service, which may mean product, reports or alarms during that period need a second look.

Adjust the interval using your own data

After a few cycles, your records start telling you what the schedule should be:

  • Always within tolerance as found, with little drift? You may be able to stretch the interval, if no rule prevents it.
  • Frequently out of tolerance as found? Shorten the interval, and ask why. The device may be wrong for the service, poorly installed, or failing.
  • Drifts every winter? Look at enclosure heating, heat tracing on impulse lines, and installation location.

Use a computerized maintenance system or even a well-kept spreadsheet so due dates do not depend on one person's memory.

Review the whole program once a year. Instruments get added, removed or change duty, and a tier 3 indicator that someone now uses to make operating decisions may deserve a promotion. Retired instruments should come off the list so crews are not chasing devices that no longer exist.

Making it manageable

Group calibrations by area or by shutdown window to reduce travel and process interruptions. Keep a small stock of spares for tier 1 devices so a failed unit can be swapped and calibrated on the bench. Tie in the loop check whenever an instrument is replaced, so the controller scaling is verified along with the device.

Our instrument calibration service can build the instrument index, set up tiers and carry out the field work, and our industrial maintenance crews can coordinate it with your electrical shutdowns.

Common questions

Is calibrating the same as a bump test on a gas detector?

No. A bump test briefly exposes the sensor to gas to prove it responds and alarms. A calibration adjusts the reading against a known gas concentration. Both are normally required, at frequencies set by the manufacturer and your workplace requirements.

Can we calibrate in place or does it have to go to a shop?

Many instruments can be calibrated in the field with portable reference equipment. Some, like certain flow meters or analyzers, are better checked on a bench or by the manufacturer. Your procedure should say which.

What does traceable mean?

It means the reference equipment used was itself calibrated against higher-level standards in an unbroken chain back to national measurement standards, with certificates to prove it.

Do we need to recalibrate after a repair?

Yes, for anything where accuracy matters. Any repair, sensor swap or re-ranging should be followed by a calibration check and, ideally, a loop check to the controller.

About this guideGeneral information, not a site assessment

Codes and permit rules change and every building is different. For work on your system, talk to a licensed electrician and your local permit authority.

Keep reading

More on instrumentation, controls and automation

All 12 guides →
Instrumentation, controls and automation · 6 min

What a loop check is and why it matters

A loop check proves that each instrument and control signal is wired, configured and displayed correctly from the field device to the operator screen. Here is what it involves and when you need one.

Read the guide →
Instrumentation, controls and automation · 8 min

Hazardous locations basics for shops and plants

What makes an area a hazardous location, how Zones and Divisions work, the common ways electrical equipment is protected, and what owners are responsible for.

Read the guide →
Instrumentation, controls and automation · 7 min

Gas detection in shops, parkades and plants

How fixed gas detection works, which sensor types suit which gases, where sensors go, and how to keep a system you can trust.

Read the guide →

Need an electrician?

Call the 24/7 line or send a request and we'll set up a consultation and a free estimate.

Call 24/7Request service