3400, 10180 101 St NW, Edmonton, AB T5J 3S424/7 service 1 (800) 716-8955
  1. Home
  2. Services
  3. Instrumentation

Service

Instrumentation

Field instruments, calibration, loop checks and gas detection, done by people who read P&IDs for a living.

CommercialIndustrial

Instrumentation services across Alberta and British Columbia: installing field instruments, calibrating them, loop checking and commissioning, and fixed gas detection, with records your team can trust.

Measurement you can trust

Every automated process depends on what its instruments report. If a level transmitter reads high, a tank can run dry. If a pressure transmitter drifts, a pump can trip for no reason or fail to trip when it should. Good control starts with good measurement.

Alberta Electrical installs and maintains process instrumentation at plants, water and wastewater facilities, commercial buildings and field sites across Alberta and British Columbia, working from our head office in Edmonton. Instrument work is done by instrument technicians, a designated trade in Alberta alongside Electrician, with our licensed journeyperson electricians handling the power, cable and raceway that feed it.

FIG 01Alberta Electrical
Tank with a level transmitter, a pump, pressure, flow and temperature transmitters on the outlet pipe and a control valve; dashed signal lines run up to a PLC box, and the flow transmitter and control valve loop is shown in orange.Instruments on a simple process linetankpumpLT101PT102FT103control valveTT104PLC / control systemprocess lineinstrument signalflow loop: FT measures, valve acts
A simplified P&ID-style sketch of a tank and pump line with level, pressure, flow and temperature transmitters wired to a control system, with the flow control loop highlighted.

On a drawing, each instrument has a tag such as FT-103, where the letters say what is measured and what the device does. We work from your P&IDs and instrument index, and we mark up anything we find in the field that does not match.

Our instrumentation services

Our instrumentation work covers four connected areas:

  • Field instrumentation: installing transmitters, switches, analyzers and valve instruments, with the tubing, wiring and supports they need.
  • Instrument calibration: checking instruments against traceable reference standards and recording as-found and as-left results.
  • Loop checks and commissioning: proving every signal from the field device to the control system screen before start-up.
  • Gas detection: fixed detectors, controllers and alarms for toxic and combustible gases.
FIG 02Alberta Electrical
Four boxes in a row labelled install, calibrate, loop check and maintain, with an orange arrow returning from maintain to calibrate, and a yellow band below for gas detection.The life of a measurement1 Installmount, tube,wire, label2 Calibratebench or inplace, record3 Loop checkfield to screen,then start-up4 Maintainverify, repair,recalibrateperiodic checks bring it back to step 2Gas detectionSafety instruments follow the same cycle, plus regular bump tests.
The four stages an instrument goes through, from installation and calibration to loop checking and ongoing maintenance, with gas detection following the same cycle.

Instrumentation rarely stands alone. A new instrument usually means new I/O in a PLC system or changes to a control panel, and often sits inside a larger plant retrofit. We can handle the whole chain so nothing falls between contractors.

Standards, hazardous locations and safety

We follow the Canadian Electrical Code (CSA C22.1) as adopted in Alberta for the wiring, and work to recognized industry practice for instrumentation, including ISA symbols and documentation conventions. In British Columbia, electrical permits go through Technical Safety BC or a municipality that runs its own permit program.

Many instruments sit in hazardous locations where flammable gas, vapour or dust may be present. Equipment there must be certified for the area classification, and wiring methods, seals and intrinsically safe barriers must match it. We confirm the classification drawings before we start rather than assuming.

SafetyProcess connections can hold energy

Impulse lines and instrument tubing can hold pressure, heat and process fluid even when the line looks idle. Isolation and draining should only be done by trained people under your site's permit and lockout procedures.

Who we work with

Our instrumentation clients include plant owners, maintenance managers, engineering firms and general contractors. Some need a full crew for a new facility. Others need one technician for a week of calibrations or a fast response to a failed transmitter.

  • Owners and operators: ongoing calibration, troubleshooting and replacement of failed instruments.
  • Engineering firms: installation and commissioning to your drawings and specifications, with field markups returned for as-builts.
  • General and mechanical contractors: instrument scope on new builds and expansions, coordinated with the rest of the electrical work.

Whatever the size of the job, you get the same thing: work done to the drawings, problems flagged early and records you can rely on.

Built for Alberta and BC conditions

An instrument that works in a warm control room can misbehave outdoors at -30 C. Impulse lines freeze, sensing fluids thicken and condensate collects in enclosures. We pay attention to heat tracing, insulated enclosures, drain points and cable entries so readings stay steady through winter and chinook thaws.

Our online job management system gives you calibration records, loop check sheets and photos in one place, and our 24/7 line at 1 (800) 716-8955 is there when an instrument fails at the worst time. All of our work is backed by our 100% satisfaction guarantee.

Questions we hear

Who does the instrument work?

Instrument work is done by instrument technicians, which is a designated trade in Alberta. Our licensed journeyperson electricians handle the power distribution, cable and raceway that support it.

Do you work outside Edmonton?

Yes. We work across Alberta and British Columbia from our Edmonton head office. In BC, permits go through Technical Safety BC or a municipality that administers its own.

Can you work in hazardous locations?

Yes. We confirm the area classification first, then use equipment and wiring methods certified for that classification, including seals and intrinsically safe circuits where they are specified.

Do you only work on new projects?

No. Much of our instrumentation work is maintenance, calibration and troubleshooting on existing facilities, including replacing obsolete instruments one at a time.

How this job runs

What to expect

  1. Review the drawings

    We review your P&IDs, instrument index and data sheets, and walk the site with your team to confirm what is installed.

  2. Plan the work

    We set the scope, isolation needs, hazardous area requirements, permits and schedule, and explain what drives the cost.

  3. Install and test

    Instrument technicians and electricians install, calibrate and loop check, working under your site's safety procedures.

  4. Hand over records

    You receive calibration certificates, loop sheets and marked-up drawings through our online job system.

Related

Instrumentation services

Instrumentation

Field instrumentation

Installation of pressure, level, flow and temperature instruments, analyzers and valve instrumentation, with tubing, wiring and documentation, for plants and facilities across Alberta and BC.

View service →
Instrumentation

Instrument calibration

Bench and in-place calibration of pressure, temperature, level and flow instruments, with as-found and as-left records, for facilities across Alberta and British Columbia.

View service →
Instrumentation

Loop checks and commissioning

Instrument loop checks, function testing and commissioning support for new plants, expansions and control upgrades in Alberta and British Columbia, with signed loop sheets and a clean punch list.

View service →
Instrumentation

Gas detection

Fixed toxic and combustible gas detection systems for plants, parkades, mechanical rooms, shops and facilities in Alberta and BC: installation, wiring, controller setup, testing and maintenance.

View service →

Guides

Read before you book

All guides →

Ready to book instrumentation?

Call the 24/7 line or send a request and we'll set up a consultation and a free estimate.

Call 24/7Request service