3400, 10180 101 St NW, Edmonton, AB T5J 3S424/7 service 1 (800) 716-8955
  1. Home
  2. Services
  3. Building automation
  4. HVAC controls

Building automation

HVAC controls

Sequences that keep people comfortable, protect equipment in the cold and stop wasting energy.

CommercialIndustrialResidential

HVAC controls for air handlers, rooftop units, boilers, heat pumps and terminal units in commercial and multi-family buildings across Alberta and BC: new sequences, retrofits, tuning and troubleshooting.

Comfort, protection and efficiency

HVAC controls decide when fans run, how far dampers open, how hot the heating water gets and when cooling starts. Well-tuned controls keep occupants comfortable with less energy. Poor ones fight themselves, heating and cooling at the same time, or trip equipment on cold mornings.

In Edmonton and across the prairies, freeze protection is a big part of the job. A coil can freeze in minutes if an outdoor air damper sticks open at -30 C. Proper sequences, sensors and interlocks protect the equipment and the building.

FIG 01Alberta Electrical
Side view of an air handler with outdoor air entering on the left through a damper, filter, yellow heating coil, orange freeze stat, cooling coil and supply fan with VFD, with supply temperature and static pressure sensors downstream.Air handling unit control pointsOA damperfilterfilter DPheating coilfreeze statcooling coilsupply fan + VFDsupply tempstaticoutdoor airto buildingFreeze protection stops the fan and closes the outdoor damper before a coil can freeze.
An air handling unit showing the outdoor air damper, filter with differential pressure switch, heating coil, freeze protection, cooling coil, supply fan with drive and supply temperature and static pressure sensors.

Equipment we control

  • Air handlers and rooftop units: economizer, heating, cooling, fan speed and static pressure control.
  • Boilers and heating plants: staging, pump control and outdoor air reset.
  • Heat pumps and VRF systems: integration with the BAS and backup heat for the coldest days.
  • Terminal units: VAV boxes, fan coils, unit heaters and electric baseboard zones.
  • Exhaust and make-up air: kitchens, shops and parkades, interlocked with the systems they serve.

Our licensed journeyperson electricians handle power and control wiring, and our controls technicians program and tune. We coordinate with your mechanical contractor for work on the equipment itself. For new equipment wiring, see heat pump wiring and air conditioner installation.

Sequences that save energy

Many buildings run on settings that made sense years ago. Fans run all night, heating water stays hot on mild days and outdoor air is brought in whether or not anyone is there. Small sequence changes can save a meaningful amount of energy without new equipment.

FIG 02Alberta Electrical
Graph with outdoor temperature from minus 30 to plus 15 C on the horizontal axis and heating water temperature on the vertical; an orange reset line slopes down between a maximum limit and a minimum limit, crossing a dashed fixed setpoint line.Outdoor air reset for a heating loophottercoolerheating water supply temperature-30 C0 C+15 Coutdoor air temperaturefixed setpoint wastes energymax limitmin limitreset line
Outdoor air reset: as the outdoor temperature rises, the heating water temperature is lowered along a reset line between set maximum and minimum limits, instead of running at one fixed setpoint.
  • Outdoor air reset on heating water
  • Supply air temperature and static pressure reset
  • Optimal start and stop around occupancy
  • Demand-controlled ventilation based on CO2 or occupancy
  • Night setback and holiday schedules

Savings depend on the building, the equipment and how it is used today. Energy metering and trend data show what is actually happening, and help prove the results after changes.

Cold-climate details that matter

Controls designed for milder climates often struggle on the prairies. We pay close attention to the details that cause most winter calls:

  • Outdoor air dampers that seal and close on fan shutdown
  • Freeze stats placed to sense the coldest air across the coil
  • Heating pumps that run whenever there is a freeze risk
  • Sensors protected from sun, wind and stratified air
  • Chinook swings that confuse heating and cooling changeover

Getting these right keeps equipment safe through cold snaps and avoids the expensive call-outs that follow a frozen coil.

Troubleshooting and service

Hot and cold complaints, nuisance alarms and equipment that will not start are often controls problems: a failed sensor, a stuck actuator, a setpoint someone changed, or a sequence that does not suit how the space is used now. We trace the problem from the screen to the field device and fix the cause.

TipWhat to tell us when you call

Note which rooms or units are affected, when it started, the outdoor temperature and any alarms on the BAS screen. Trend screenshots are very helpful. Our 24/7 line is 1 (800) 716-8955.

Every service visit is recorded in our online job management system, with changes to setpoints or programs noted so the next technician knows what was done.

Questions we hear

Why is one room always too hot or too cold?

Common causes are a badly placed or failed sensor, a stuck damper or valve, an undersized zone or a sequence that does not fit how the space is used. Trend data usually points to the cause.

Can you improve controls on old equipment?

Often, yes. Adding sensors, an economizer upgrade or a new controller can make older equipment run better, as long as the equipment itself is sound.

How do you protect coils from freezing?

With freeze stats, proper damper control, minimum outdoor air limits, pump control and alarms. The exact approach depends on the unit and coil type.

Do you work on residential HVAC controls?

Our HVAC controls work is mainly commercial and multi-family. For homes, see our heat pump wiring and in-floor heating services.

How this job runs

What to expect

  1. Review and trend

    We review drawings and sequences, and trend the system to see how it actually runs.

  2. Recommend changes

    We explain problems and options in plain language, with what each change involves.

  3. Implement

    Sensors, actuators, wiring and program changes are made in planned windows with occupants in mind.

  4. Verify and document

    We confirm results with trend data, update sequences and graphics, and record changes.

Related

More in Building automation

Service

Building automation

Building automation for commercial, institutional and multi-family buildings across Alberta and British Columbia: BAS installation, HVAC controls, lighting control systems and energy metering.

View service →
Building automation

BAS installation

Building automation system installation for new buildings, additions and control replacements across Alberta and BC: controllers, networks, sensors, wiring, graphics and commissioning.

View service →
Building automation

Lighting control systems

Occupancy sensing, daylight harvesting, scheduling and networked lighting controls for offices, schools, warehouses, retail and multi-family buildings across Alberta and British Columbia.

View service →
Building automation

Energy metering

Electrical, gas and water submetering for commercial, industrial and multi-family buildings across Alberta and BC, connected to your BAS or an energy dashboard.

View service →

Guides

Read before you book

All guides →
Instrumentation, controls and automation · 7 min

Gas detection in shops, parkades and plants

How fixed gas detection works, which sensor types suit which gases, where sensors go, and how to keep a system you can trust.

Read the guide →
Instrumentation, controls and automation · 7 min

What a building automation system does

A plain-language look at building automation: what it controls, how it is put together, and how owners and operators use it to save energy and catch problems early.

Read the guide →
Instrumentation, controls and automation · 7 min

Building automation for small and mid-size buildings

Practical building automation options for offices, retail, clinics, churches, schools and light industrial buildings, and how to choose one you can live with for years.

Read the guide →

Ready to book hvac controls?

Call the 24/7 line or send a request and we'll set up a consultation and a free estimate.

Call 24/7Request service