The short version
A building automation system (BAS), sometimes called a building management system or BMS, is the network of controllers, sensors and software that runs a building's mechanical and electrical systems automatically. It decides when the heat comes on, how much fresh air the air handlers bring in, when the parkade fans run, and who gets an alarm when a boiler trips at 3 a.m. in January.
Done well, a BAS keeps people comfortable, saves energy and gives operators early warning of problems. Done poorly, it becomes a black box that everybody overrides.
You will find a BAS in most offices, schools, hospitals, recreation centres, apartment buildings and warehouses of any size. Even when the equipment is modern and efficient, the controls decide how much of that efficiency you actually get.
What it typically controls
- Heating plant: boilers, pumps, heating loops, often with outdoor air reset.
- Ventilation and air handling: fans, dampers, coils and heat recovery.
- Cooling: chillers, rooftop units, cooling towers and heat pumps.
- Zone control: VAV boxes, fan coils, radiant valves and thermostats.
- Exhaust and parkade ventilation, often tied to gas detection.
- Lighting, through lighting control systems.
- Metering and monitoring: electricity, gas and water sub-meters, plus alarms from equipment like generators, sump pumps and elevators.
Fire alarm and life safety systems are separate systems with their own rules. A BAS may receive signals from them, for example to shut down air handlers, but it does not replace them.
How the pieces work together
At each piece of equipment, a controller reads sensors and drives actuators to hold a setpoint. Here is an air handler as the BAS sees it:
Controllers talk over a building network. Open protocols such as BACnet let devices from different manufacturers share data, which matters when you want to add equipment later or change service providers. The front end, either a workstation or a web interface, is where people view graphics, change schedules and setpoints, look at trends and handle alarms.
Schedules, setpoints and sequences
Most energy savings come from three things: running equipment only when needed, holding sensible setpoints, and making systems cooperate rather than fight.
- Schedules set occupied and unoccupied times. Holiday schedules matter too.
- Setpoints define the temperatures, pressures and levels the system aims for.
- Sequences of operation are the written rules for how each system behaves, including start-up, reset strategies and what happens on a failure.
Ask your operator or service provider for a list of points in manual override. Overrides put in during a cold snap or a complaint often stay in place for years and quietly waste energy.
Trends and alarms: the operator's tools
A BAS stores trends, the history of temperatures, valve positions and equipment status. Trends let you see whether a room was actually cold, whether a valve is hunting, or whether equipment is running overnight for no reason.
Alarms tell people when something needs attention: a boiler failure, a freeze-stat trip, a high temperature in a server room. Like any alarm system, they need tuning so that the important ones stand out.
Signs your BAS needs attention
- Occupants complain about the same rooms every season, and the fix is always a manual override.
- Equipment runs nights and weekends when the building is empty.
- Heating and cooling run at the same time in the same space.
- Alarms are so frequent that nobody reads them, or so rare that you wonder if they work.
- Graphics show sensors reading impossible values, like a room at -40 C.
- Only one person or one contractor knows how to log in.
These are common, and most are fixable without replacing the system. Sensor calibration, sequence corrections and alarm cleanup often pay back quickly in comfort and energy. Where hardware is obsolete, controllers can usually be replaced in phases, much like migrating obsolete PLCs.
Getting more from the system you have
Many buildings have a capable BAS that is underused. A short tune-up can review schedules, clear overrides, check sensors and update graphics. For smaller properties, see BAS options for small and mid-size buildings, and for tracking results, sub-metering and energy dashboards.
Our BAS installation and HVAC controls services cover new systems, expansions and service on existing ones.
Common questions
Is a BAS the same as a smart thermostat?
A smart thermostat controls one zone or unit. A BAS coordinates many pieces of equipment, shares data between them and gives a central view. Some small buildings do well with networked thermostats; larger ones generally need a BAS.
What is BACnet?
BACnet is an open communication protocol for building automation, developed by ASHRAE and widely supported. It lets controllers and software from different manufacturers exchange data.
Can a BAS control our electric heat?
Yes. A BAS can schedule and control electric baseboards, unit heaters and in-floor heat through relays or contactors, and can help limit peak demand.
Who should have the passwords?
The owner, at an administrator level, as well as the service provider. Make sure accounts are individual and that former staff and contractors are removed.
Codes and permit rules change and every building is different. For work on your system, talk to a licensed electrician and your local permit authority.